Simplicity 1694920 Betreibershandbuch Seite 1

ATTACHMENTOPERATOR’SMANUAL42” Snowthrower AttachmentMfg. No. Description1694920 42” Single-Stage Snowthrower42” Single-Stage Snowthrower1733943Revisio

8General Operating InstructionsSnow Removal Suggestions• Determine the best snow removal pattern beforebeginning. • Wind direction is an important fac

9MaintenanceSchedule For Normal CareGeneral LubricationLubricate the snow thrower as shown in Figure 2. Wherean oil can is shown use 30 weight oil. W

10Troubleshooting, Adjustments, & ServiceTROUBLESHOOTINGWhile normal care and regular maintenance will extendthe life of your equipment, prolonged

11Troubleshooting, Adjustments, & ServiceFigure 3. Adjusting Skid ShoesSkid Shoe Adjustment On smooth surfaces such as concrete or asphalt, thescr

12Troubleshooting, Adjustments, & ServiceLift Adjustment In the fully raised position the attachment should be 4”-5”off the ground. LIFT HEIGHT AD

13Troubleshooting, Adjustments, & ServiceFigure 7. Belt RoutingA. V-PulleyB. Idler PulleyC. Electric Clutch Pulley (V-pulley)D. Snow thrower Pulle

44QQTTYYQQTTYY44661516171410987651312113142Ref Qty Description1 1 UPPER WIRING HARNESS2 2 REFLECTORS3 1 FINAL WIRING HARNESS4 1 CHUTE ROTATION SWITCH5

15Initial Setup & AssemblyABDECFigure 9. Chute AssemblyA. Chute Rotator Drive Cover BoltB. Chute Rotator Drive CoverC. Chute Rotator Drive Assemb

16Initial Setup & AssemblyFigure 13. Hitch Latch Pin InstallationFigure 12. Hitch InstallationA. Hitch AssemblyB. Hitch Support ShaftC. Hitch Mo

ABCDDEE17Initial Setup & Assembly7. Lift the hitch (B) and from the left side of the tractor,slide hitch latch pin (A) through the mounting hole i

18Initial Setup & AssemblyABDECDFigure 17. Lift Arm and LinkageA. Lift Arm AssemblyB. Mounting Bolts and NutsC. Lift Arm LinkageD. Quick ClipE. L

19Initial Setup & AssemblyABCFigure 19. Upper Wiring HarnessA. SwitchB. Female ReceptacleC. Rotation Motor Power LeadsABCDFigure 20. Wiring Harn

20RemovalSnow Thrower Removal1. Fully raise and support the snow thrower with woodenblocks.2. Loosen the turn buckle (C, Figure 21) and thenremove the

21Removal7. Disconnect the final wiring harness (B, Figure 24). 8. Remove both quick clips (E, Figure 25) and snowthrower mounting pins (D).9. Move th

22Removal11. Slide the hitch assembly (A, Figure 27) forwards untilthe hitch mounting arms (C) are free of the hitch sup-port shaft (B).12. Slide the

23Notes

500 N Spring Street / PO Box 997Port Washington, WI 53074-0997www.MasseyLawn.comMANUFACTURING, INC.500 N Spring Street / PO Box 997Port Washington, W

1Table of ContentsMaintenanceSchedule for Normal Care ...9General Lubrication ...9Tr

2Safety Rules& InformationThis machine is capable to amputating hands and feet and throwing objects. Read these safety rules andfollow them close

3Safety Decals7. Always observe safe refueling and fuel handling prac-tices when refueling the unit after transportation orstorage.8. Always follow th

4Safety DecalsPart No. 1716532Auger Danger DecalPart No. 1722674Discharge Chute Danger DecalPart No. 1716531Main Operation Warning DecalWHEN OPERATING

5Required AccessoriesRequired AccessoriesIt is required that tire chains and two rear wheel weights or Quick Tach Weights are used.Never operate on sl

Features &Controls6TRACTOR CONTROLSBefore you begin operating the tractor and attachment,make certain you have:• Read and understood the instructi

7General OperatingInstructionsChecks Before StartingIMPORTANT NOTE: Refer to Tractor Operator’s Manualfor important information concerning safely stor